Returns- Returns must be communicated by customers within 7 days of delivery and sent back within 30 days to receive a refund. No returns without authorization will be accepted. All returns must be accompanied by a copy of the receipt and a note. All items must be returned complete and in new condition. 

All returns are subjected to 20% processing and restocking charge after the product has been inspected. The shipping cost will not be refunded. 

Refunds will be made back to the same method of payment when ordering those parts. We will not refund a different method of payment. 

Non-returnable Items Include- Close Outs and Clearance Items, Special Orders, Custom Orders, Used Parts, and Cut to Length Items. (Other items may apply)

Shipping: All orders are shipped UPS Ground, UPS Surepost or USPS Priority when ordering online. Shipping charges are calculated based on weight, size, and quantity of boxes in addition to processing and handling including insurance. All shipping charges are the customer's responsibility (even if charges online are not the same as emailed or phone orders).

All standard shipping orders will be shipped within a day or two on weekdays. Orders placed on the weekend (Fri-Sun) will be shipped Monday or Tuesday or the first weekday after a holiday. Custom or Handbuilt Products may require more time to be built before shipping. For any reason, an order may be delayed or prevented you will be contacted through phone and/or email. 

Express/2nd Day/Next Day Shipments:  Express orders must be made by phone orders only! Orders placed after 12:00 p.m. CST. will be processed the Next Business Day. UPS will only guarantee next day shipment. If you choose 2nd-day shipments expecting it before the weekend, UPS does not guarantee its arrival 

Additional Fees: Double Check that the address you gave is correct. You may be charged additional fees to redirect your package to the correct address. 

PO Boxes: We can ship to PO Boxes using USPS. However, UPS will only accept shipments to a valid street address. They do not deliver to P.O. Boxes. 

International Shipping: International buyers are responsible for paying duties, taxes, and applicable customs brokerage fees separate from the merchandise cost. Buyers will generally pay these fees upon receipt of your shipment. Buyers may be charged additional fees once they receive the package. Read our international policy here. 

Paypal: All orders paid by a verified PayPal account will be shipped to the address on the Paypal account to comply with Paypal's policy. No Exceptions.

UPS Estimated Shipping Lead Times

USPS Estimated Shipping Lead Times 

Instructions for the EC 360D-1 Diaphragm Carburetor for the Briggs Raptor/Flathead Limited Engine

Click Here for a Downloadable PDF of the 360D-1 Instructions

Installation

Intake Manifold: Use only EC Built intake manifolds or adaptors. Our intakes are designed with tapered solid pulse ports. The pulse angle allows a better signal to the carburetor's pulse hole, which controls the pump inside the carburetor. Do not sure manifolds that are only notched for the pulse port. They do not provide a good signal or match the carburetor gasket. Your engine will often have a specific manifold designed to bolt to your cylinder head with minimal change in port size and angle. 

Carburetor Gasket: Make sure you are using the correct carburetor gasket that matches the bore of the carburetor and the intake manifold. When installing the gasket, make sure the 1/8" pulse hole is clear and matches the hole on the intake and carburetor. If the hole is not open or partially closing off the pulse port, the carburetor's pump will not function properly, causing erratic tuning problems. 

Carburetor Mounting:

1. Slide the carburetor over the studs.
2. Look to make sure the studs are not too long, so the carburetor will seal to intake appropriately.
3. Torque the nuts a little on each side of the carburetor one at a time to tighten evenly.
4. Do not over-tighten one side over the other to not break or crack the flange on the carburetor. 

Air filter: Attach our recommended air filter to your carburetor. Always use an air filter cleaner. This filter has more than enough capacity not to restrict airflow. There is no gain by not running an air filter. That would only damage your expensive carburetor and engine. 

Linkage: When running your throttle cable, make sure you have a throttle pedal stop to prevent the throttle from excessive pulling resulting in damaging the throttle shaft and or butterfly and carburetor body. Check our website for throttle cable installation guides. 

Fuel Systems and Related Service Information

Fuel Tanks: Make sure your fuel tank is vented correctly. Vented fuel caps may not vent well enough, becoming clogged or covered, causing a restriction to fuel flow to the carburetor simulating a carburetor tuning problem. Poor venting causes a vacuum in the fuel tank the fuel pump can't overcome, causing the carburetor to go lean. The engine will usually not turn rpm and go flat like a soft rev limiter. 

Fuel Pump: Only use our recommended fuel pumps. 4-cycle pumps differ from 2-cycle pumps, and many knock-offs do not flow enough fuel for racing applications especially running methanol. 

Fuel Filter: To keep the trash out of your fuel pump and, more importantly, your carburetor, we recommend that you use a Walbro In-line fuel filter(Part# 125-512). As it ages, the fuel flow through it will be restricted. Inspect and replace regularly as needed.

Fuel Line: We recommend methanol or a chemical-resistant fuel line. Like the fuel filter, your line will wear out, so replace it when needed over time. Check for kinks in the fuel line to ensure fuel flow is not restricted.

Tuning Instructions

To study these instructions thoroughly for a better racing experience with your new carburetor.

Idling: DO NOT MOVE THE IDLE SCREW IN SO THAT THE CARBURETOR WILL IDLE. Only turn the idle speed screw in just enough to cushion the shutter from hitting hard against the throttle bore. If you set the carburetor where it will idle, the carburetor could have a bad flat spot when it comes off the turn. Idling makes tuning very difficult and ultimately ineffective. In your level of racing, it's challenging to find an advantage if you idle your carburetor. Do not idle! Keep it running with your foot.

Starting Position:

1. Refer to these tuning sheets enclosed with your carburetor for on-track performance.
2. Set the needle 1 turn(s) out on the high side, and 2-1/2 turns out on the low side for a starting position.
3. Again be sure that the carburetor idle screw is set where it just cushions the throttle plate when it closes but not open enough so that the engine can idle.
4. Start the engine and pull onto the track.
5. Give the engine a couple of easy laps to warm up.
6. Be sure in these warm-up laps that you are running the engine in a spot where it is running clean.

4-Cycle Carburetor Tuning: Using our starting positions, you should only need to tune the high side needle, but we will go through adjusting both needles for your education. 

First: Now, with the engine under full throttle, it should run clean to the end of the longest straightaway. If the engine shuts off then comes back on by itself before you get to the end of the longest straightaway, this is more than likely because the carburetor is set too rich on the high side needle. The cure here is to take the high side needle in 1/8 turn increments (leans out) until the engine pulls clean the entire length of the straightaway.

Second: Now, bring your engine down to parade lap speed. Accelerate hard as you would for the starting line break. If you have a flat spot or a bogging condition, the carburetor is lean on the low side needle. Come out 1/8 of a turn on the low side needle and try again. Keep coming out on the low side needle until the engine pulls hard with no bog or flat spot. Now try the same test coming off the turn. You should be satisfied once the acceleration pulls hard and clean. We have the low side started at 2.5 turns out you do not need to turn this needle in any more than a 1/8, or if you are tuning the low side by riching the fuel mixture, do not go further than 3 turns out; the needle could back out and fall out of the carburetor. You will need to contact us to diagnose a problem or recalibrate the low side circuit. 

Third: Once you have this basic setup, repeat the first and second steps to fine-tune even further. As you can see, the tuning of a Tillotson/EC Carburetor on a 4/Cycle engine is a delicate balance between the high and low side needle adjustments plus the pop-off pressure of the carburetor. As you lean in the high side needle for the best top-end power, you also lean out the bottom a touch. So to assure yourself of good cornering speed and no flat spots of the bottom, you need to go back now and check this under a pull once more.

Maintenance

Race service to your carburetor is straightforward and can easily be done by you. Many pain-staking hours have gone into this unit to increase air and fuel flow. The following information is to help you in your racing efforts by educating you more on the workings of your carburetor and how to service it to keep its peak performance.

Flushing your Carburetors: All engines. Methanol fuel is a very high corrosive type of fuel and should never be left in alloy fuel tanks or the carburetor when the day or night of racing is over. Be sure to flush the tank, fuel pump, and carburetor with gas. We like a mixture of 16oz Marvel Mystery Oil and 1-gallon non-ethanol gas for a gas flush. You do this by draining the methanol out of your tank and replacing it with your flushing gas mixture(Note: Flushing an alloy tank out with gas could get you DQ'd with a water test.) The carburetor and fuel pump have the methanol flush out of them. As far as fuel tanks go, a plastic fuel tank is our choice for methanol fuel. If you have a plastic tank or fuel cell, just pull the fuel line off the fuel inlet fitting and have a can of your flushing gas mixture with a piece of fuel line and attach it to the fuel inlet of the fuel pump. Next, start the engine and let it run long enough to use at least 3-6 oz of your flushing gas mixture or until the engine begins to stumble. 

Fuel Inlet Cap: Look for cracks and wear. Take care of it because it can't stand to take a lot of abuse.

Main Metering Diaphragm (Black): This needs to be replaced after every three to five races. You know when the main diaphragm deteriorates if the throttle response on your carb gets lazy beyond tuning.

Fuel Pump Diaphragm: Located above the demand diaphragm. This diaphragm/skin should be replaced every race day for optimized performance.

Fuel Strainer Screen: Remove and clean after each race to assure ample fuel flow.

Fuel Strainer Cover Gasket: Replace when showing signs of shrinkage.

Inlet Needle: Replace every 5 to 6 races or when you can't hold pop-off pressure. 

Pop-Off Pressure: The pop-off pressure of your Tillotson Carburetor is a very critical tuning factor and will have a direct bearing on the pressure level of the carburetor. Here at the shop, we have set the pop-off pressure to be very close to your track needs.

Here are some helpful hints on pop-off pressure changes. The lower altitude racetracks and good heavy air will let you run lower pop-off pressure. The higher the altitude racetracks have less usable air to burn, so in turn, the pop-off pressure needs to be set higher to cut down on the amount of fuel for the carburetor to mix with the usable air. Add shims to raise the pop-off pressure from where we have set it. Remove shims from under the pop-off spring or change the spring to lower the pop-off pressure. For the spring chart and other information, go to our website: eccarburetors.com.

Under no circumstances stretch a pop-off spring or cut one off enough where it has one leg standing down. If for some reason, you can't get the carburetor to pop off and hold, this is a sign that the needle seat or inlet needle has foreign material/trash on it. To solve this, try replacing the inlet needle and cleaning the inside of the seat with WD40 and a Q-tip. If this does not resolve the problem, you may need to send your carburetor to us for a service.

Carburetors are like any mechanical device. The user needs to understand the unit and the proper tools to maintain and service it to ensure maximum performance levels. In the Tillotson Service Kit, you will find the following tools and what they do (also have Walbro and Mikuni)

Pop-off Pressure Gauge: This is a must-have tool for the Tillotson Carburetor owner. With this tool, you can check the inlet pressure of the needle and seat assembly and leak down the amount for proper performance. (POPG1 15PSI) (POPG2 30PSI)

Fulcrum Arm Gauge: With this tool, you can adjust the proper arm height of the fulcrum arm for the amount of fuel delivery needed.

Needle and Seat Socket: This specially machined socket removes the needle and seat for cleaning.

Diaphragm and Rebuild Kits: This Carburetor uses a P6-MDG gasket and a P8-MRK as a rebuild kit. The rebuild kits come with a seat and seat gasket; we do not advise using these parts on your rebuild unless, in the extremely rare circumstance, the seat gasket is leaking (We highly recommend you send your carburetor in for us to fix it at that point). Replacing the seat can strip the threads and ruin your carburetor if not appropriately handled. 

Our techs are here to help you get the most from our carburetors, but we are in no way responsible for any damage to your carburetor once it leaves our workbench. There are no warranties or returns on any carburetors or parts.